Liquid Sealant
Code: D176404M2
Price:
$11.70
MSRP: 33
Quantity in Basket:
None
Material
Anthracite coloured, solvent-free sealing, adhesive & coating compound based on silicone. Once completely bonded, REINZOSIL is virtually odorless.
Properties
This highly elastic universal sealing compound is resistant to mineral oils and numerous synthetic oils, lubricants, petrol, diesel oil, greases, hot and cold water, detergents, sunlight, ozone, and sea water.
REINZOSIL is suitable for continuous operation in the temperature range between -50 °C and +250 °C (briefly up to 300 °C).
Hardness (softness) lies in the range of 30 to 35 Shore A.
Application
Due to its special properties, REINZOSIL is used in the most varied applications, e.g. as FIPG (formed-in-place gasket) for wet assembly, i.e. for sealing small gaps under pressure as well as for cylinder liners in piston machines, and also to compensate for extensive component warping. Moreover, the compound is also used to seal constructional fissures or cracks, and for seals that are subjected to considerable relative movement.
Contrary to REINZOPLAST, the sealing layer is destroyed during disassembly, and a new coating is required after the surfaces have been cleaned.
The compound can also be applied to assembled components. In these cases, after the sealing joint has been cleaned and degreased, REINZOSIL is applied directly to the sealing gap, similar to the procedures used in the building industry.
Instructions for use
Remove any gasket remnants or other residues such as grease, oil, etc. with RE-MOVE solvent remover. Allow the surfaces to dry, then apply the sealing compound on one side manually or by means of a pneumatic spraying device. Assemble the components immediately.
Processing temperature lies between +5 °C and +40 °C. Depending on temperature and humidity, a skin develops after 5 to 12 minutes. The full curing time depends mainly on the relative air humidity (RH) and room temperature, as well as on the thickness (gap height) and width of the applied layer.
The following applies:
The higher that air humidity and temperature are, or the thinner and narrower the sealing layer is, the shorter will the curing time be. With a layer or gap width of e.g. 7 mm, and a thickness or gap height of 1,5 mm at 40 °C and 90 % RH, the full curing time is about 9 hours, provided that temperature and humidity have access to both sides. With the above sealing gap dimensions, but at normal ambient conditions (approx. 23 °C and 50 % RH), curing time would be about 100 hours. Fully cured (vulcanized) material can only be removed mechanically.
Part #: 70 31414 10
Anthracite coloured, solvent-free sealing, adhesive & coating compound based on silicone. Once completely bonded, REINZOSIL is virtually odorless.
Properties
This highly elastic universal sealing compound is resistant to mineral oils and numerous synthetic oils, lubricants, petrol, diesel oil, greases, hot and cold water, detergents, sunlight, ozone, and sea water.
REINZOSIL is suitable for continuous operation in the temperature range between -50 °C and +250 °C (briefly up to 300 °C).
Hardness (softness) lies in the range of 30 to 35 Shore A.
Application
Due to its special properties, REINZOSIL is used in the most varied applications, e.g. as FIPG (formed-in-place gasket) for wet assembly, i.e. for sealing small gaps under pressure as well as for cylinder liners in piston machines, and also to compensate for extensive component warping. Moreover, the compound is also used to seal constructional fissures or cracks, and for seals that are subjected to considerable relative movement.
Contrary to REINZOPLAST, the sealing layer is destroyed during disassembly, and a new coating is required after the surfaces have been cleaned.
The compound can also be applied to assembled components. In these cases, after the sealing joint has been cleaned and degreased, REINZOSIL is applied directly to the sealing gap, similar to the procedures used in the building industry.
Instructions for use
Remove any gasket remnants or other residues such as grease, oil, etc. with RE-MOVE solvent remover. Allow the surfaces to dry, then apply the sealing compound on one side manually or by means of a pneumatic spraying device. Assemble the components immediately.
Processing temperature lies between +5 °C and +40 °C. Depending on temperature and humidity, a skin develops after 5 to 12 minutes. The full curing time depends mainly on the relative air humidity (RH) and room temperature, as well as on the thickness (gap height) and width of the applied layer.
The following applies:
The higher that air humidity and temperature are, or the thinner and narrower the sealing layer is, the shorter will the curing time be. With a layer or gap width of e.g. 7 mm, and a thickness or gap height of 1,5 mm at 40 °C and 90 % RH, the full curing time is about 9 hours, provided that temperature and humidity have access to both sides. With the above sealing gap dimensions, but at normal ambient conditions (approx. 23 °C and 50 % RH), curing time would be about 100 hours. Fully cured (vulcanized) material can only be removed mechanically.
Part #: 70 31414 10